This morning I once again tried to cook some squirrel. I didn't expect to be successful because have ruined more squirrels than I can remember. Once I tried to stew one, but the potatoes turned to mush and the meat didn't even cook. Next day I baited a fox set with that same meat... and the next morning I got a red fox. That's great and all, but just goes to say I couldn't cook. Well, last night I was looking through Horace Kephart's book Woodcraft and Camping, and I found a good recipe for biscuits and one for squirrel. I cooked them up, and... they were great! So I want to share the recipes with y'all.
For the biscuits, mix 1 cup of flour, 1/2 teaspoon baking powder, and 1/6 teaspoon salt in a Zip-Lock bag. Keep this until you are ready to make the biscuits. When you're ready to cook them, add about 1/3 to 1/2 tablespoon of Crisco and mix it with a wooden spoon really well. Then add water until it's a thick dough. Be sure to mix with a wooden spoon and not your hands. Now that the dough is ready, you can form your biscuits and bake 'em fer 15-20 minutes. This will make about 4 biscuits. At the end of this article I will show you how I made my oven.
As for the squirrel(s), cut em up into pretty small pieces and parboil them. Now take them out of the water, season them, and fry them in Crisco until the outside is a light brown. I would advise eating with gravy.
The oven I cooked my biscuit in this morning was very simple. I took a small cup with a lid, although you can do it with any size, and cut a piece of hardware cloth that would fit into the cup when it was set sideways. Like an oven rack. Then I just covered it in two layers of tinfoil. All I had to do was put the biscuit on the rack, put the lid on, and set it in some good coals. If you are confused, look at the picture.
This was my breakfast this morning, and like I said, it was great. I hope you enjoy the recipe,
-Caleb
Friday, April 28, 2017
Thursday, March 23, 2017
The Making Of a Knife-Via Pictures
The knife starts out as a lawnmower blade.
And shaped,
Then the shape is cut out and ground.
Next, a bevel or grind is put on, and holes drilled.
Then it is hardened. this is done by heating to a orange color, then quenching in oil.
Then it is polished and tempered in an oven set @ 400 degrees.
The handle scales are cut out, and drilled.
And evened up at the top.
It is epoxied and clamped.
Shaped,And shaped,
And finished!
Tuesday, February 28, 2017
How to Make a File Knife - Stock Removal
Today we are going to be making a knife from a very common
and
cheap tool; a file.
To begin with, you will need to find a file a
sufficient size for the knife you want to make. Usually you can find these at
flea markets and garage sales pretty cheap. The other materials you will
need for this project are: some pretty hardwood like maple, some 1/4"
brass pin stock, a grill, charcoal, heat-proof tubing of some kind, ( for making a forge) a
hair drier and some two part epoxy.
Your tool checklist will include: a belt
sander or file, a drill and
1/4" metal cutting drill bit, a small ball
peen hammer, tongs or long vice grips, a hacksaw or bandsaw, clamps and a paint
can of any kind of oil.
First we are going to
make our forge. To begin with, drill a hole the size of your pipe in the bottom
of your grill. Now secure the pipe in the hole, with about ½" sticking up
in the bottom of the grill. Then duct tape the hair dryer to the other end of
the pipe. When the hair dryer is on, it supplies a constant flow of air to your
fire on top, and we will use it for the hardening and annealing of our knife.
Note: if you are confused, YouTube making a forge, there are a lot of detailed
videos there.
Begin by starting up the forge with lump charcoal and turning on the blower. Now
heat as much of the file as you can to a dull red. If you need, you can heat
one side up, then flip it and do the other side. Once both sides have been or
are red, bury the file in sand. Once it cools, it is ANNEALED, meaning it is as
soft as it can get. Now, using a bench grinder or file, you can shape your
knife.
Once you have the shape you like, it's on to the next step: putting on the bevel.
Once you have the shape you like, it's on to the next step: putting on the bevel.
To grind the bevel, you need a belt sander with metal
abrasive
belts. If you do not have one of these, a very rough file will work as
long as your metal is annealed. Using a file is tedious, but you are not going
to mess up easily at all. With a grinder, always have your would-be blade up.
First establish a good 20 degree bevel, then by rotating your wrist minutely
clockwise you can make the grind line get taller each pass on the grinder. Once
you have the grind established, keep thinning it out until the edge is about as
thick as the a piece of paper. DO NOT GET IT SHARP. If you do this, the edge will
melt off in the hardening process and ruin the blade.
Now you need to drill your holes. If you are not using a brand new drill bit,
it won't cut. (A little tip: use Ace brand drill bits, they are the best for
this kind of stuff) And if you didn't anneal your metal, the drill will not cut
at all. That said, position your holes where you want them, and drill away. I
really advise using a drill press for this, and if you don't have one, try to
find a friend that has one and will let you use it.
Once you have done all of
this, it is time for the heat treat. Get your forge fired up, and place
your blade in the hottest part of the coals. Make sure the hair dryer
is going good, and get the blade part up to a bright orange color. Once the
entire cutting edge part is orange, grab it with your pliers and dunk the blade
in your oil. But don't just dunk it, move it around in the oil. This helps air
pockets from forming on the knife and lessens the chance of warping. This is
called hardening.
(And it MUST be oil; water will not work, for it is too
violent of a quench. If you were to quench it in water, it would get tiny
little cracks in the blade that would grow in size with use of the knife and
ruin the blade)
Take it out and run a file loosely across the edge. If it
slides over with no catching, it is hardened. If the file bites into the metal,
it did not harden properly and you need to try again. After this, take your
knife and check it for warping. If it warped, DO NOT HAMMER ON IT. The knife is
very brittle and would break. Heat the knife up to a red and then bang on it
and re-harden it.
If your knife was straight, put it in the oven set for 400
degrees and leave it there two hours. When you're ready, take it out
with pliers and dunk it in some water. This process is called tempering; it
takes some of the hardness out of the knife and ensures a good edge. Now take
your knife back to the sander or file and take all of the scale off of the
bevels. Now you can get it as sharp on the grinder as you want.
OK, on to the handle. First, trace the handle of your knife
onto a piece of your hard wood, twice. Using a bandsaw or hacksaw, cutting
outside of the line, cut the pattern you traced out. Now position one of these
slabs underneath the actual handle, get it how you want it, and drill holes
that line up exactly with the ones in your file. Do the same with the other
side.
Now cut two 1 ½" lengths of your pin stock and put them into the
holes. Once done, you can do the pre-final sanding and profiling of the handle
with the pins holding the wood in place where it will be when it's all said and
done. Once you have the shape of the wood slabs lined up with the tang of the
knife, take the pins out and cut them down until, when they are slid into the
holes, there is only 1/8" protruding on each side.
Now take all of the
parts and set them out. The handle slabs should be inside-up and the pins
should be easily accessed. Now mix your epoxy, and smear a thin layer in both
sides of the tang and the insides of the handle slabs. Line all the holes up,
and insert the pins. Now take the back of your ball-peen hammer and peen the
pins over gently on each side until they are good and flat. Clamp it up good,
but not so tight that you squeeze all the epoxy out.
Once the epoxy cures, you can do the final shaping on your sander... or with sandpaper. When you have a shape you like, rub the handle
down with a few coats of oil, and ... viola, you have a file knife.
Wednesday, October 5, 2016
The Cheap Haversack Kit
By Caleb Steck
This kit is designed to be carried in a belt pouch and a haversack. Consequently, it must be quite light. Everything must be absolutely necessary. You are not going to be carrying things like a draw shave, or even a tarp.
That said, let’s start with cutting tools. First is a quality belt knife. (Click HERE to see an article on that issue) The 4 basics of a good belt knife are: full tang, good grind and temper, and a comfortable handle. My bush knife is homemade, which cost me about $7, some charcoal, and about 2 hours of work, but I already had the forge. (Click HERE to see how make a very basic knife) If you were to buy a bushcraft knife new, it would cost about anywhere from $10 to upwards of $150. But, if you went to a few flea markets, you could find an Old Hickory butcher knife for around $3.
Next is a belt hatchet. My favorite is the Gerber pack hatchet, but that is rather expensive. The other option is to search flea markets. Look for an old carpenter’s hatchet that’s suits you, and re-furbish it. This is my preference, for if you can find an old hatchet, it was usually made really well. I also carry a “hobo tool” that was my grandpa’s which has a large 4” blade, a smaller blade, spoon, fork, 2 awls, wood saw, scissors, file, cork screw, can opener and a bottle opener. Almost all of these tools I would carry anyway, so having them all in one folding tool is a big bonus.
Moving on to containers, I have a wooden kuska that is great as a traditional water cup, and I even made the gouge I used to carve it. Next I use a tin can cookset I made, consisting of the following: 1) 18 oz soup can with the sharp inside rim crimped down, 1) 14 oz soup can that nests inside of the other can upside down creating a container, a soda can with the top cut off and the edge crimped down (which nests inside of the smaller can), and my sugar, salt and ‘Ol bay seasoning inside it all.
Note: if you are planning to stay for longer periods of time, or there is more than one person camping, add a larger pail that can carry gear, but will be used to make soups in.
Next I have a water bottle, as large as possible, a few plastic bags and a supply of tin foil. For food, I use a bag of rice, a bag of oatmeal, cooking oil, jerky, and a fishing kit.
During squirrel season I also take along a good gun and a gun care kit, which is paper towels, hex wrench set, plastic bags, a length of bankline with loops on each end for a gambrel string, and a pocket knife (which everybody should already have).
My main fire source is cotton balls and Carmex, which burns even better than petroleum. Carmex has petroleum, bee’s wax AND certain kinds of oil, all of which are fuel sources. Besides that, I have a lighter and ferro rod in my pocket, and my fire kit. It contains char cloth, a piece of flint, waterproofed strike-anywhere matches, and extra Carmex.
Another thing I have is a leather belt pouch that I made, which contains my fishing kit, electrical tape, compass, and is a place for my fire kit.
That concludes the contents if the scrounged belt kit, and I put mine all together almost free. Just scrounging and blacksmithing alone will knock a lot off the cost of this kit. So, while you can go buy $200 worth of brand new gear at Academy, if you keep your eyes open and learn a little blacksmithing, well you can have a $20 worth of gear and you even know how it was built!!
The Ultamate Bush Knife
The Ultimate Bush knife
Ok, right out of the gate I am going to tell you this; there is no one-size-fits-all ultimate bush knife, it doesn’t exist. But I can describe one the most useful knives for bushcrafting in the south. First you must have a full tang. A Mora type knife would be great for carving, but not batoning and chopping. You want enough stability to know that that handle is not going any where. Second, you need a good grind and shape. I like a little lower grinds, where they maybe come halfway op the blade. My preferred handle material is micarta; it is pretty much indestructible, and is also water resistant. As long as it is good carbon steel, most any steel will work. 1095 is mostly what I work with; it provides good hardness and you can strike sparks off the blade in an emergency. And the last of these specs is size. I prefer larger handles, like 4 ½ inches. The blade length should be in between 4 and 6 inches. Now I am going to build the knife we just described, and then show you how well it works.
Ok, two days later here is what I have:
So, the above is a great example, and I would, without a second’s hesitation, trust my life to this knife. But, going back to my previous point, there is no perfect knife. In my opinion an old hickory butcher knife from Amazon or a flea market is a fantastic bush tool, although it is not as sturdy as a thicker knife. Any knife that fits in the categories listed at the top of this article is a good bush knife.
Well, I hope this little tidbit helped you,
and keep on bushcrafting,
-Caleb
Friday, September 30, 2016
Hunting Seasons
Just a reminder, hunting seasons start up soon, so be sure to check the parks and wildlife website for your state, that's where the dates are posted. For Texas the website is tpwd.texas.gov. For wood and smith counties fore sure, SQUIRREL SEASON STARTS TOMORROW!
Subscribe to:
Posts (Atom)













